QVL
(Redirected from Audio-HAT-card)
Jump to navigation
Jump to search
Qualified Vender List
Contents
Wi-Fi Adapters & Dongles
| Brand | Model |
|---|---|
| ASUS | USB-AC56 (RTL8812AU) |
| ASUS | USB-AC68 (RTL8814AU) |
Audio DAC
Audio DAC (GPIO HAT)
Audio HAT(hardware-attached-on-top) cards
The Tinker Board supports some HiFiBerry and IQAudIO Audio HAT cards.
You can enable one of them by Device Tree Overlay: add the following line at '/boot/hw_intf.conf' as below.
dtoverlay=hifiberry-dac
| Brand | Model | IC | dtoverlay file | Status | Image | I2S Mode | Note |
|---|---|---|---|---|---|---|---|
| HiFiBerry | HiFiBerry DAC+ Light | PCM5102a | hifiberry-dac | Released | 2.0.3 | Master | |
| HiFiBerry | HiFiBerry DAC+ PRO | PCM5122 | hifiberry-dacplus | Support | 2.0.6 | Slave | only support on Tinker Board S |
| HiFiBerry | HiFiBerry DAC+ Standard (RCA) | PCM5122 | hifiberry-dacplus | Released | 2.0.3 | Master | |
| HiFiBerry | HiFiBerry AMP+ | TAS5713 | hifiberry-amp | Released | 2.0.3 | Master | |
| HiFiBerry | HiFiBerry Digi+ Standard | WM8804 | hifiberry-digi | Released | 2.0.5 | Slave | only support on Tinker Board S |
| IQaudIO | IQAudio Pi-Digi+ | WM8804 | iqaudio-digi-wm8804-audio | Released | 2.0.5 | Slave | only support on Tinker Board S |
| IQAudio | IQAudio Pi-DAC+ | PCM5122 | iqaudio-dacplus | Released | 2.0.3 | Master | |
| IQAudio | IQAudio Pi-DAC Pro | PCM5242 | iqaudio-dacplus | Released | 2.0.3 | Master | driver as same as PCM5122 |
| IQAudio | IQAudio Pi-DigiAMP+ | TAS5756m | iqaudio-dacplus | Released | 2.0.3 | Master | |
| Hiton Audio | Tube-Pi | PCM5122 | hifiberry-dac | Released | 2.0.5 | Master | |
| JustBoom | DAC HAT | PCM5122 | justboom-dac | Released | 2.0.5 | Master | |
| JustBoom | DAC Zero | PCM5121 | justboom-dac | Released | 2.0.5 | Master | driver as same as PCM5122 |
| JustBoom | Amp HAT | TAS5756m | justboom-dac | Released | 2.0.5 | Master | |
| JustBoom | Amp Zero | TAS5756 | justboom-dac | Released | 2.0.5 | Master | Amp Zero can only supply 5V/1.5A to TinkerBoard through GPIO, but TinkerBoard needs 5V/3A. So just use the TinkerBoard's power though 40pin header, do not use external power supply connected to Amp Zero. |
| JustBoom | Digi HAT | WM8804GEDS | justboom-digi | Released | 2.0.5 | Slave | only support on Tinker Board S |
| JustBoom | Digi Zero | WM8804GEDS | justboom-digi | Released | 2.0.5 | Slave | only support on Tinker Board S |
Audio DAC (USB)
| Brand | Model |
|---|---|
| ASUS | ASUS Xonar U5 |
| ASUS | ASUS Xonar U7 |
Display/Panel
Powertip
| Size | Resolution | Interface | Touch | Power | Brightness / Control* | |||||
|---|---|---|---|---|---|---|---|---|---|---|
| Name | X | Y | ||||||||
| 4.3 | WQVGA | 480 | 272 | HDMI-RBG | v | VBus | 5V | 0.5A | 850 | A/B/C |
| 4.3 | WQVGA | 480 | 272 | HDMI-RBG | v | Pj1 | 12V | 0.25A | 850 | A/B/C |
| 5 | WVGA | 800 | 480 | HDMI-RBG | v | VBus | 5V | 0.7A | 850 | A/B/C |
| 5 | WVGA | 800 | 480 | HDMI-RBG | v | Pj1 | 12V | 0.45A | 850 | A/B/C |
| 7 | WVGA | 800 | 480 | HDMI-RBG | v | Pj1 | 12V | 0.5A | 850 | A/B/C |
| 7 | WVGA | 800 | 480 | HDMI-RBG | v | Pj1 | 12V | 0.42A | 450 | A/B/C |
| 7 | WSVGA | 1024 | 600 | HDMI-RBG | v | VBus | 5V | 0.95A | 450 | A/B/C |
| 10.1 | WXGA | 1280 | 800 | HDMI-LVDS | v | Pj1 | 12V | 0.6A | 450 | A |
| 10.1 | WXGA | 1280 | 800 | HDMI-LVDS | v | Pj1 | 12V | 0.6A | 450 | A/B/C |
Note*: A:GPIO PWM B:Gesture C:USB Protocol
For more inquiries, please contact us at TinkerBoard@asus.com
Others
| Brand | Model |
|---|---|
| Pi Supply | Flick HAT |
| Pi Supply | PaPiRus Zero |
| Pi Supply | Flick Large |
| Pi Supply | PaPiRus ePaper |
| Pi Supply | Flick Zero |
| Pi Supply | Pi PoE Switch HAT |
| Pi Supply | Bright Pi |
| Pi Supply | Pi Supply Switch |
| Pi Supply | PiJuice HAT |